ArcelorMittal

Steel grades for Hot rolled sections

All the sections can be delivered in steel grades according to EN 10248-1, but not all sections are available in all steel grades. Below table summarizes the current possibilities. Special steel grades like S 460 AP, American ASTM A 572 steel grades, steels with improved corrosion resistance like AMLoCor® and ASTM A 690, or steels with copper addition in accordance with EN 10248 Part 1 Chapter 10.4 can be supplied on request. A modified steel grade A 690 with higher yield strength is also available upon request. Please contact us for updated information.

Galvanisation has an influence on the chemical composition of the steel and must therefore be specified in the purchase orders. We strongly recommend informing us of all surface treatment to be applied to the product when placing orders. ArcelorMittal can also provide steel grades complying with other standards (see table below). 
  

Steel Grades of sheet pile section

 

Steel grade  EN 10248 Comparable International Standards
  Min. yield strength Min. tensile strength Min. elongation  USA Canada  Japan
  ReH Rm Lo=5,65√So  ASTM  CSA JIS
  MPa MPa  %      
S 240 GP 240 340 26      
S 270 GP 270 410 24 A328 Gr.260W SY295
 S 320 GP 320 440 23   Gr.300W  
S 355 GP 355 480 22 A572Gr.50 A690 Gr.350W  
S 390 GP 390 490 20 A572Gr.55  Gr.400W   SY390  
S 430 GP 430 510 19 A572Gr.60    

 

ArcelorMittal Mill specification

     
S 460 AP 460 550 17 A572Gr.65    

 

AMLoCor®

Mechanical properties and chemical composition
AMLoCor® Min. yield strength Min. tensile strength Min. elongation Chemical composition (weight % max)
  ReH Rm Lo=5,65√So                
  MPa MPa  % C Mn Si P S N Cr Al
Blue 320 320 440 23 0.27 1.70 0.60 0.05 0.05 0.011 1.50 0.65
Blue 355 355 480 22 0.27 1.70 0.60 0.05 0.05 0.011 1.50 0.65
Blue 390 390 490 20 0.27 1.70 0.60 0.05 0.05 0.011 1.50 0.65

Some sheet pile sections are not available in AMLoCor® steel grade. For more information click on this link: AMLoCor®

 

Tolerances on Sheet Piles

Tolerances AU, PU, GU AZ AS 500 HZ, HZM
Mass ±5 % ±5 % ±5 % ±5 %
Length ±200mm ±200mm ±200mm ±200mm
Height H≤200mm:±4.0mm H≤200mm:±5.0mm - ± 7.0mm
H> 200mm:±5.0mm 200mm<H<300mm: ±6.0mm  -
H≥300mm : ±7,0mm  -
Thickness t,s≤8.5mm: ±0,5mm t,s≤8.5mm: ±0.5mm -

t,s ≤ 12.5mm:
 -1.0/+2.0mm

t,s > 8.5 mm :±6% t,s > 8.5 mm :± 6 % t,s > 8.5 mm: ±6%  t,s > 12.5mm
-1.5 / +2.5mm
Width  ±2%
Double pile width  ±3%
Straightness  0,2% of the length
Ends out of square  ±2% of pile width

Reduced tolerances on request.